Copper Cable Tests
♦♦Copper Cable Tests♦♦
Most of the copper cable installed today is twisted-pair of one form or another, and the number of individual wire connections involved makes the installation and testing process more complicated than for other cable, particularly in light of the various standards available for the connector
pinouts.
♦♦Wire Mapping♦♦
Wire mapping is the most basic and obvious test for any twisted-pair cable installation. For twisted-pair cables, you must test each cable run to make sure that the individual wires within the cable are connected properly,
A perfunctory wire-mapping test can be performed visually by simply checking the pinouts at both ends of the cable. However, problems can occur that are not visible to the naked eye. A proper wire-mapping tester can detect any of the following faults:
♦ Open pair occurs when one or more of the conductors in the pair are not connected to a pin at one or the other end. In other words, the electrical continuity of the conductor is interrupted. This can occur if the conductor has been physically broken or because of incomplete or improper punch-down on the IDC connector.
♦ Shorted pair occurs when the conductors of a wire pair are connected to each other at any location in the cable.
♦ Short between pairs occurs when the conductors of two wires in different pairs are connected at any location in the cable.
♦ Reversed pair (sometimes called a tip/ring reversal) occurs when the two
wires in a single pair are connected to the opposite pins of the pair at the other end of the cable.
♦ Crossed pairs Crossed (or transposed) pairs occur when both wires of one color pair are connected to the pins of a different color pair at the opposite end.
♦ Split pairs occur when the wire from one pair is split away from the other and crosses over a wire in an adjacent pair. Because this type of fault essentially requires that the same mistake be made at both ends of the connection, accidental occurrence of split pairs is relatively rare.
♦Wire-mapping faults are usually caused by improper installation practices, although some problems like opens and shorts can result from faulty or damaged cable or connectors. The process of testing a connection’s wire mapping is fairly straightforward and requires a remote unit that you attach at one end of the connection and a main unit for the other end.
The main unit simply transmits a signal over each wire and detects which pin at the remote unit receives the signal.
Các bài kiểm tra cáp đồng
Hầu hết cáp đồng được lắp đặt hiện nay là cáp đôi xoắn, và số lượng kết nối dây cá nhân liên quan làm quá trình lắp đặt và kiểm tra phức tạp hơn so với cáp khác, đặc biệt là considering các tiêu chuẩn khác nhau cho chân cắm kết nối.
Bản đồ dây (Wire Mapping)
Bản đồ dây là bài kiểm tra cơ bản và rõ ràng nhất cho bất kỳ lắp đặt cáp đôi xoắn nào. Đối với cáp đôi xoắn, bạn phải kiểm tra mỗi đoạn cáp để đảm bảo các dây cá nhân trong cáp được kết nối đúng cách.
Một bài kiểm tra bản đồ dây cơ bản có thể được thực hiện trực quan bằng cách kiểm tra chân cắm ở cả hai đầu cáp. Tuy nhiên, các vấn đề có thể xảy ra mà không thể nhìn thấy bằng mắt thường. Một thiết bị kiểm tra bản đồ dây phù hợp có thể phát hiện các lỗi sau:
Dây đôi mở (Open pair): Xảy ra khi một hoặc nhiều dây dẫn trong đôi không được kết nối với chân ở một hoặc cả hai đầu cáp.
Dây đôi ngắn mạch (Shorted pair): Xảy ra khi dây dẫn của một đôi dây được kết nối với nhau tại bất kỳ vị trí nào trong cáp.
Ngắn mạch giữa các đôi (Short between pairs): Xảy ra khi dây dẫn của hai dây khác nhau được kết nối tại bất kỳ vị trí nào trong cáp.
Dây đôi ngược (Reversed pair): Xảy ra khi hai dây trong một đôi được kết nối với chân ngược lại ở đầu kia của cáp.
Dây đôi chéo (Crossed pairs): Xảy ra khi cả hai dây của một đôi màu được kết nối với chân của đôi màu khác ở đầu kia.
Dây đôi tách (Split pairs): Xảy ra khi dây từ một đôi bị tách ra và chéo qua dây trong đôi lân cận.
Lỗi bản đồ dây thường do thực hành lắp đặt không đúng cách, mặc dù một số vấn đề như mở và ngắn mạch có thể kết quả từ cáp hoặc kết nối bị lỗi.
Quá trình kiểm tra bản đồ dây của một kết nối khá đơn giản và yêu cầu một đơn vị từ xa được gắn ở một đầu kết nối và một đơn vị chính cho đầu kia. Đơn vị chính chỉ truyền tín hiệu qua mỗi dây và phát hiện chân ở đơn vị từ xa nhận tín hiệu.
hashtag#RCDD Knowledge
Last updated
Was this helpful?