Pulling or Blowing method for the optic fiber cables ?
Last updated
Was this helpful?
Last updated
Was this helpful?
Pulling or Blowing method for the optic fiber cables ? 👌 ♦Pulling method : •Pulling rope pre-installed •Equipment and manpower at two sides •High sidewall forces on cables and ducts •may lead to cable damage •Mainly manual pulling is practiced. •Machine pulling needs one hydraulic power pack •Mainly used for straight duct route •Suitable for short distance (few 100m) installation ♦Blowing method : •No pulling rope to install •Equipment and manpower at one side •Forces on cable and duct can be monitored and •controlled and minimal chance of cable damage •Large compressor and/or hydraulic power •pack at one side •Preferred for duct route with multiple •bends and undulations •Preferred for long distance (over 2km) installation ♦Cable blowing is the process of installation of optical fiber cable into a pre-installed duct. ♦Compressed air is injected in the duct inlet after few hundred meters of cable is pushed into the duct. ♦Compressed air flows at high speed through the duct and along the cable. The pushing force is applied mainly near the cable inlet by a pushing device. ♦♦The most important point to be considered♦♦ ♦Duct Fill Ratio (DFR) The ratio between cable and duct size is known as ‘Duct Fill Ratio’. There are two methods to calculate it : a) The ratio between cross sectional area of cable and inner space of the duct. DFR = d2/D2 x 100 Where, d= cable diameter D= duct inner diameter For optimum blowing performance DFR to be kept between 35 to 65%. b) The ratio between cable diameter and duct inner diameter. DFR = d/D x 100 For optimum blowing performance DFR to be kept between 30 to 80%. For conventional cable of diameter equal or larger than10 mm: 30 to 50% For micro cable of diameter 1-9 mm: 30 to 80% Higher DFR helps to achieve longer blowing distance particularly in straight route. Higher DFR also prevents cable buckling effect particularly for cables with low stiffness. However, high DFR may result in shorter blowing distance in the route having multiple bends. Therefore, an optimized DFR needs to be maintained to achieve best blowing performance.
Tỷ lệ lấp đầy ống dẫn (Duct Fill Ratio - DFR).
Tỷ lệ giữa kích thước cáp và ống dẫn.
Công thức tính DFR: a) DFR = (d2/D2) x 100 (diện tích cắt ngang). b) DFR = (d/D) x 100 (kích thước đường kính).
Giá trị DFR tối ưu: 35-65% (phương pháp a) và 30-80% (phương pháp b).
DFR cao giúp tăng khoảng cách thổi, đặc biệt là đường thẳng.
DFR cao cũng ngăn chặn hiệu ứng gập cáp.
Tuy nhiên, DFR cao có thể giảm khoảng cách thổi trong đường ống có nhiều khúc quanh.
Yếu tố quan trọng
Cáp quang được đẩy vào ống dẫn.
Không khí nén được.inject vào đầu ống dẫn.
Không khí chảy nhanh qua ống dẫn và cáp.
Lực đẩy được áp dụng gần đầu cáp.
Quy trình thổi cáp quang
Không cần dây kéo.
Thiết bị và nhân công chỉ cần tại một đầu.
Forces lên cáp và ống dẫn có thể được kiểm soát.
Ít khả năng hư hỏng cáp.
Cần máy nén khí và nguồn thủy lực.
Phù hợp cho đường ống có nhiều khúc quanh.
Phù hợp cho lắp đặt dài (trên 2km).
Phương pháp thổi
Dây kéo đã được lắp đặt sẵn.
Thiết bị và nhân công cần thiết tại hai đầu.
Forces cao lên cáp và ống dẫn.
Có thể gây hư hỏng cáp.
Chủ yếu sử dụng kéo thủ công.
Máy kéo cần nguồn thủy lực.
Phù hợp cho đường ống thẳng.
Phù hợp cho lắp đặt ngắn (vài trăm mét).
Phương pháp kéo
Có hai phương pháp chính để lắp đặt cáp quang: kéo và thổi.
Phương pháp kéo hoặc thổi cáp quang
Knowledge